Save energy without changing a single habit.
Your meter measures. EcoSense watches — every appliance, every zone, all month — then tells you in plain rupees where the waste is hiding.
Your bill tells you what.
Never why.
You already track your usage. The real cost is invisible waste — the fridge running warm, the geyser left on, the appliance quietly drawing extra power for weeks before you notice.
This is your home, right now.
Seven zones, drawing simultaneously. Your monthly bill compresses all of this into one number and one date.
One room. A fifth of the load.
Drawn right now in a single living room. Nothing on your bill tells you which room, or which appliance inside it.
And the largest slice is "other".
The biggest single draw in most homes is the one nobody can name. That's where the waste lives — and where EcoSense starts looking.
Twelve months of blind spending.
That's how long a faulty appliance typically overdraws before anyone notices — one full billing year, paid in full.
The power you pay for while nothing is on.
Every idle device in that pile is still drawing. EcoSense finds them individually, names them, and prices them.
Standby consumers detected in a typical 2BHK
One plug-in device.
One app. Your pattern.
Tips built around your own home's usage — not generic advice from a national average.
Plug in once
Attaches to your existing meter or appliance point in under 5 minutes. No rewiring, no electrician.
It learns your pattern
The app profiles your household's own baseline usage across every zone in the home.
It coaches you monthly
Personalized tips and a savings report, benchmarked against the same month last year.
Geyser drawing 40% above normal
That's the difference between a meter that measures and an app that watches out for you. Same alert for a spiking fridge, an AC left running, or a heater cycling all night.
It sits beside the meter you already have.
One module, one status ring. It reads what your meter reads — then keeps reading it, all month, appliance by appliance, so nothing slips past a billing cycle unnoticed.
What would you
actually save?
Tick what runs in your flat. The maths below is the same model EcoSense applies to a real home — shown in full, so you can argue with it.
What runs in your home
0 selectedHow this is worked out. Consumption is (watts × hours × 30) per device, plus standby draw for the hours it sits idle. Savings apply three rates: 80% of measured standby load once EcoSense names the culprits, 14% of AC and geyser running load from right-sized run-times, and 5% of everything else from the monthly personalized report. Early fault detection is valued at ₹3,500 (repair before failure vs. replacement) spread over 24 months. These are planning estimates for a typical urban Indian home, not a guarantee — your own first monthly report shows the real number.
Your geyser and your AC
are the whole argument.
Between them they are usually the largest controllable line item on an urban Indian bill. EcoSense learns when they actually need to run — and the savings model above applies its 14% right-sizing rate to exactly these two.
Not another smart meter.
A ₹1,500 smart meter tells you numbers. EcoSense tells you what to do about them — the same difference as the two bulbs beside this text.
one-time — no subscription
device + premium personalized insights
Built for exactly
this housing society.
A society is a cluster of near-identical homes on the same tariff slab, the same weather, the same appliance mix. That's precisely the pattern EcoSense is built to learn from.
Benchmarking that means something
See how your usage compares to similar flats in your own block — not a generic national average.
Rollout discount potential
Multiple households adopting together typically unlocks better install scheduling and support.
Word-of-mouth you can verify
Ask any neighbour already on a personalized report — the tips are specific enough to fact-check instantly.
The honest answers.
Isn't a plain smart meter enough?
Only if you already know how to read raw wattage data and act on it fast. Most people don't — that's the ₹1,500 gap.
Is installation disruptive?
No rewiring. It's a plug-in device, set up in under 5 minutes, with no electrician visit needed.
What if I don't save enough to justify ₹199 a month?
The monthly report shows your exact savings against last year. You'll see the number rather than take our word for it.
Does it work with solar?
Yes. The dashboard shows solar yield relative to your home's usage, alongside every appliance zone.
Save energy without
changing a single habit.
₹4,500 device. Setup in under 5 minutes. Your first personalized report lands in your first billing month.
Questions? Ask right after the meeting — happy to walk through your own flat's numbers.